Trophic transfer of heavy metals across four trophic levels based on muscle tissue residuals: a case study of Dachen Fishing Grounds, the East China Sea.

In this study, we collected 56 species of fishery organisms (including fish, crustaceans, cephalopods, gastropods, and bivalves) from four seasonal survey cruises at the Dachen fishery grounds. We measured the concentrations of seven heavy metals (Cd, Zn, Cu, Pb, Cr, As, and Hg) in these fisheries organisms. We determined their trophic levels using carbon and nitrogen stable isotope techniques. We analyzed the characteristics of heavy metal transfer in the food chain. The results showed significant differences in heavy metal concentrations among different species. Among all biological groups, bivalves and gastropods exhibited higher levels of heavy metal enrichment than other biological groups, while fish had the lowest levels of heavy metal enrichment. Heavy metals exhibited different patterns of nutritional transfer in the food chain. While Hg showed a biomagnification phenomenon in the food chain, it was not significant. Cd, Zn, Cu, Pb, Cr, and As exhibited a trend of biodilution with increasing nutritional levels, except for As, which showed no significant correlation with δ15N.

Chemomechanical Origins of the Dynamic Evolution of Isolated Li Filaments in Inorganic Solid-State Electrolytes.

The penetrating growth of Li into the inorganic solid-state electrolyte (SSE) is one key factor limiting its practical application. Research to understand the underlying mechanism of Li penetration has been ongoing for years and is continuing. Here, we report an in situ scanning electron microscopy methodology to investigate the dynamic behaviors of isolated Li filaments in the garnet SSE under practical cycling conditions. We find that the filaments tend to grow in the SSE, while surprisingly, those filaments can self-dissolve with a decrease in the current density without a reversal of the current direction. We further build a coupled electro-chemo-mechanical model to assess the interplay between electrochemistry and mechanics during the dynamic evolution of filaments. We reveal that filament growth is strongly regulated by the competition between the electrochemical driving force and mechanical resistive force. The numerical results provide rational guidance for the design of solid-state batteries with excellent properties.

Comparison of 3 diagnostic methods for pulmonary tuberculosis in suspected patients with negative sputum smear or no sputum.

STUDY DESIGN: To explore the diagnostic value of 3 methods for sputum smear-negative and non-sputum patients with suspected pulmonary tuberculosis (TB). METHODS: This prospective study enrolled sputum smear-negative and non-sputum patients with suspected TB admitted to Jiangxi Chest Hospital between January 2020 and December 2022. The 3 methods were bronchoalveolar lavage fluid (BALF)-acid-fast bacillus (AFB) smear, GeneXpert MTB/RIF, and gene chip for Mycobacterium strain identification. The diagnostic performance of the 3 tests was evaluated with BALF Mycobacterium culture + BALF-AFB smear + GeneXpert MTB/RIF + Gene chip as the gold standard. RESULTS: A total of 456 samples were collected from 114 patients with suspected TB. Twenty-four patients were diagnosed with TB. The combination of GeneXpert MTB/RIF and gene chip for Mycobacterium strain identification yielded the highest area under the receiver operating characteristics curve (AUC) of 0.953 and had sensitivity of 90.57%, specificity of 100%, positive predictive value (PPV) of 100%, negative predictive value (NPV) of 92.42%, accuracy of 95.61%. GeneXpert MTB/RIF achieved AUC of 0.906, sensitivity of 81.13%, specificity of 100%, PPV of 100%, NPV of 85.92%, accuracy of 91.23%. BALF-AFB smear had AUC of 0.519, sensitivity of 3.77%, specificity of 100%, PPV of 100%, NPV of 54.46%, and accuracy of 55.26%. The combination of GeneXpert MTB/RIF and gene chip for Mycobacterium strain identification yielded the highest κ of 0.911, while BALF-AFB smear had the lowest κ value of 0.040. CONCLUSION: For TB in sputum smear-negative and non-sputum patients using BALF Mycobacterium culture + BALF-AFB smear + GeneXpert MTB/RIF + Gene chip as the gold standard, BALF-AFB smear showed low diagnostic performance, while, though GeneXpert MTB/RIF and gene chip had good diagnostic performance, combining GeneXpert MTB/RIF and gene chip improved the diagnostic value to a great extent.

Opposite Mechanical Preference of Bone/Nerve Regeneration in 3D-Printed Bioelastomeric Scaffolds/Conduits Consistently Correlated with YAP-Mediated Stem Cell Osteo/Neuro-Genesis.

To systematically unveil how substrate stiffness, a critical factor in directing cell fate through mechanotransduction, correlates with tissue regeneration, novel biodegradable and photo-curable poly(trimethylene carbonate) fumarates (PTMCFs) for fabricating elastomeric 2D substrates and 3D bone scaffolds/nerve conduits, are presented. These substrates and structures with adjustable stiffness serve as a unique platform to evaluate how this mechanical cue affects the fate of human umbilical cord mesenchymal stem cells (hMSCs) and hard/soft tissue regeneration in rat femur bone defect and sciatic nerve transection models; whilst, decoupling from topographical and chemical cues. In addition to a positive relationship between substrate stiffness (tensile modulus: 90-990 kPa) and hMSC adhesion, spreading, and proliferation mediated through Yes-associated protein (YAP), opposite mechanical preference is revealed in the osteogenesis and neurogenesis of hMSCs as they are significantly enhanced on the stiff and compliant substrates, respectively. In vivo tissue regeneration demonstrates the same trend: bone regeneration prefers the stiffer scaffolds; while, nerve regeneration prefers the more compliant conduits. Whole-transcriptome analysis further shows that upregulation of Rho GTPase activity and the downstream genes in the compliant group promote nerve repair, providing critical insight into the design strategies of biomaterials for stem cell regulation and hard/soft tissue regeneration through mechanotransduction.

Precessing jet nozzle connecting to a spinning black hole in M87.

The nearby radio galaxy M87 offers a unique opportunity to explore the connections between the central supermassive black hole and relativistic jets. Previous studies of the inner region of M87 revealed a wide opening angle for the jet originating near the black hole1-4. The Event Horizon Telescope resolved the central radio source and found an asymmetric ring structure consistent with expectations from general relativity5. With a baseline of 17 years of observations, there was a shift in the jet's transverse position, possibly arising from an 8- to 10-year quasi-periodicity3. However, the origin of this sideways shift remains unclear. Here we report an analysis of radio observations over 22 years that suggests a period of about 11 years for the variation in the position angle of the jet. We infer that we are seeing a spinning black hole that induces the Lense-Thirring precession of a misaligned accretion disk. Similar jet precession may commonly occur in other active galactic nuclei but has been challenging to detect owing to the small magnitude and long period of the variation.

Realizing Holistic Charging-Discharging for Dendrite-Free Lithium Metal Anodes via Constructing Three-Dimensional Li+ Conductive Networks.

Lithium (Li) metal is a promising candidate for next-generation anode materials with high energy densities. However, Li dissolution/deposition processes are limited at the upper surface in contact with the electrolyte, which brings a locally high current density and then results in dendritic Li growth. This restraint of the local surface reaction during cycling has not been solved by commonly used modification strategies. In this study, a three-dimensional (3D) Li+ conductive skeleton is activated from atomic layer deposition (ALD) coating Li3PO4 (LPO) on the surface of the Ni foam (LPNF). Then, the skeleton is efficiently constructed in the Li metal anode by the lower-temperature Li infusion. Ionic conductor LPO layers and electronic conductor Ni fibers supply charge transport channels between the electrolyte and the internal Li. The mixed conductive network realizes holistic charge transfer, which is proved by in situ scanning electron microscopy experiments. In virtue of dispersive dissolution/deposition and optimized electrochemical kinetics brought by a Li+ conductive network, the composited Li electrode presents an excellent symmetric battery cycling stability (over 1200 h) and enhanced rate performances (stable cycling even at 10.0 mA cm-2). When matching with a LiCoO2 (LCO) cathode, LCO||Li@LPNF full batteries exhibit a capacity retention of 80.8% over 250 cycles. During cycling, there was no evidence of dendrite growth and the remaining Li in the composited anode showed a smooth, compact, and well-combined condition with LPNF. Through constructing a 3D Li+ conductive network, the composited Li metal anode breaks through the limit of the local surface reaction; this work proposes a novel insight of realizing holistic charging/discharging for the dendrite-free Li metal anode.

Ultralong Lifespan for High-Voltage LiCoO2 Enabled by In Situ Reconstruction of an Atomic Layer Deposition Coating Layer.

Although the rapid development of electrical energy storage devices has slowed down environmental pollution, their large-scale application has posed huge challenges to battery-related mineral resources; thus, extending the lifespan of high-voltage lithium cobalt oxide (LCO) is of great importance. Surface oxide coating is considered as the most common low-cost modification method for addressing unstable cycling performance. However, studies have shown that the oxide layer would further react with an electrolyte, while the investigation on the corresponding component evolution is lacking. Herein, a typical example utilizing the above reaction to realize surface reconstruction is presented. Applying atomic layer deposition (ALD), originally, an ultrathin Al2O3 layer is coated on the LCO surface; however, this coating layer has undergone reconstruction after reacting with electrolyte decomposition products during the cycling. Compared with simple coating, the in situ formed Li3AlF6 layer has a tighter binding to the LCO surface while possessing good Li+ conductivity and electrochemical stability. In addition, the unique properties of the ALD technology allow us to achieve ultrathin (1 nm) and conformal coating, which is beneficial for electronic conductivity and cycling stability. Furthermore, the surface phase transition layer stripping failure mechanism has first been revealed to explain the loss of Co and O, while the reconstructed Li3AlF6 effectively suppresses the surface stripping. Thus, excellent high-voltage performance has been realized (an 89% capacity retention after 1000 cycles at 4.5 V and an 88% capacity retention after 200 cycles at 4.6 V). This work casts a new understanding on the surface reconstruction of the oxide coating layer, which is also significant for other electrode materials' modification.

Nutritional value and bioaccumulation of heavy metals in nine commercial fish species from Dachen Fishing Ground, East China Sea.

The study evaluated the nutritional quality in muscle tissues of nine commercially important marine fish species. And the concentrations of trace metals (i.e. As, Hg, Cu, Pb, Cr, Cd and Zn) in the muscles (edible part) and tissues (gill and liver) of fishes caught from Dachen fishing ground, the coast of Zhejiang Province, East China Sea, were determined, and the values of target hazard quotient (THQ) and the carcinogenic risk (TR) were calculated for assessing human health risk. Significant differences(P < 0.05) were observed in the proximate chemical composition of fish muscles in these species. The muscle protein content of fish species ranged from 12.36 to 23.41%. The muscle lipid content of fishes ranged from 0.48 to 2.54%. The accumulation capacity of heavy metals (except Cr) in livers and gills was higher than that in muscles. In addition, the accumulation ability of most fishes is related to the water layer they live, the fishes living in the demersal layer showed more accumulation of heavy metals than the middle-upper layer(except Cu). Estimated daily intake (EDI), target hazard quotient (THQ), hazard index (HI) and the carcinogenic risk (TR) assessed for potential human health risk implications suggest that the values were within the acceptable threshold for human. However, the carcinogenic risk(TR) of As and Cr was close to the critical limit (10-4). Therefore, in order to ensure the health and safety of human consumption, the continuous monitoring of heavy metals in Dachen fishing ground area is suggested.

Highly efficient and blue-emitting CsPbBr3 quantum dots synthesized by two-step supersaturated recrystallization.

Highly efficient and blue-emitting CsPbBr3 quantum dots were successfully synthesized by two-step supersaturated recrystallization under ambient condition. This method could control the particle size within 2.8 nm, thus resulting in strong quantum confinement effect of the products. The as-synthesized CsPbBr3 quantum dots presented outstanding optical properties with highest photo-luminescence quantum yield of 87.20% and longest PL lifetime of 12.24 ns. The blue light-emitting diode made from the CsPbBr3 quantum dots exhibited a CIE coordinate (0.14, 0.10), in good agreement with the standard blue CIE coordinate (0.14, 0.08) of National Television System Committee (NTSC).

Atomically ordered non-precious Co3Ta intermetallic nanoparticles as high-performance catalysts for hydrazine electrooxidation.

Nano-ordered intermetallic compounds have generated great interest in fuel cell applications. However, the synthesis of non-preciousearly transition metal intermetallic nanoparticles remains a formidable challenge owing to the extremely oxyphilic nature and very negative reduction potentials. Here, we have successfully synthesized non-precious Co3Ta intermetallic nanoparticles, with uniform size of 5 nm. Atomic structural characterizations and X-ray absorption fine structure measurements confirm the atomically ordered intermetallic structure. As electrocatalysts for the hydrazine oxidation reaction, Co3Ta nanoparticles exhibit an onset potential of -0.086 V (vs. reversible hydrogen electrode) and two times higher specific activity relative to commercial Pt/C (+0.06 V), demonstrating the top-level performance among reported electrocatalysts. The Co-Ta bridge sites are identified as the location of the most active sites thanks to density functional theory calculations. The activation energy of the hydrogen dissociation step decreases significantly upon N2H4 adsorption on the Co-Ta bridge active sites, contributing to the significantly enhanced activity.

Boosting oxygen evolution of single-atomic ruthenium through electronic coupling with cobalt-iron layered double hydroxides.

Single atom catalyst, which contains isolated metal atoms singly dispersed on supports, has great potential for achieving high activity and selectivity in hetero-catalysis and electrocatalysis. However, the activity and stability of single atoms and their interaction with support still remains a mystery. Here we show a stable single atomic ruthenium catalyst anchoring on the surface of cobalt iron layered double hydroxides, which possesses a strong electronic coupling between ruthenium and layered double hydroxides. With 0.45 wt.% ruthenium loading, the catalyst exhibits outstanding activity with overpotential 198 mV at the current density of 10 mA cm-2 and a small Tafel slope of 39 mV dec-1 for oxygen evolution reaction. By using operando X-ray absorption spectroscopy, it is disclosed that the isolated single atom ruthenium was kept under the oxidation states of 4+ even at high overpotential due to synergetic electron coupling, which endow exceptional electrocatalytic activity and stability simultaneously.

Unveiling the thickness-dependent mechanical properties of graphene papers by in situ SEM tension.

With more and more applications, the mechanical strength of graphene paper (GP) has attracted significant attention in recent years. In this report, GPs were prepared by flow-induced filtration of electrochemical exfoliated graphene sheets. By adjusting the concentration of solution, we found graphene sheets fabricated in 0.1 M K2SO4 have the thinnest average thickness. And by uniaxial in-plane tensile tests operated on a self-developed in situ scanning electron microscopy (SEM) tensile stage, the corresponding GP has the best fracture strength of 192 MPa. This is due to that the thickness decrease of exfoliated graphene will increase the quantity of interlayer crosslinks, thus improving the mechanical properties of GPs. This research may open a new way to obtain high-strength GPs for applications.

Bioinspired Concentric-Cylindrical Multilayered Scaffolds with Controllable Architectures: Facile Preparation and Biological Applications.

Multilayered objects are the most important and interesting structures in nature, exhibiting multiple functionalities. Inspired by the excellent structural-functional characteristics of nature creatures, concentric-cylindrical multilayered scaffolds were prepared by a combination of melt extrusion and leaching, in which well-defined alternating microlayer/gap is assembled. Furthermore, the macroscopic shape, internal structure, and surface topography of such a multilayered scaffold can be elaborately prepared by a simple physical process. The whole process has low cost, is efficient, and is environmentally friendly. Furthermore, such multilayered scaffolds show some interesting applications, e.g., lipophilic/hydrophilic drugs delivery and cell self-seeding. Considering the facile preparation process and versatile applications, this study will open up a new pathway to fabricate scaffolds with controllable architectures and expand their biodegradable polymer applications.